Drive Train

0%

A vehicle with a lot of driveline vibration could have:

Correct! Wrong!

The two methods of drive line alignment are the parallel method and:

Correct! Wrong!

Before beginning any service or repair to a drive system:

Correct! Wrong!

The prime function of a drive line is to:

Correct! Wrong!

The main drawback of using a single cross universal joint applied to a driveshaft system is that:

Correct! Wrong!

Propeller shafts must be as short as possible and as large in diameter as possible to:

Correct! Wrong!

The two most significant factors in reducing driveline failure is:

Correct! Wrong!

To check a two-joint assembly for alignment, you must perform dial indicator tests at three different locations on:

Correct! Wrong!

What should a technician do when replacing a support bearing assembly?

Correct! Wrong!

A transfer case with an air actuator will not shift from the low gear ratio up to 1:1. The most likely first check is:

Correct! Wrong!

A truck has non-functional speedometer while the odometer operates correctly. The LEAST likely cause of the problem would be:

Correct! Wrong!

A technician finds dirt contamination when removing the 4X4 axle end-locking hub. What should the technician do?

Correct! Wrong!

The following are all acceptable steps to prepare the vehicle for a driveline angle measurement EXCEPT:

Correct! Wrong!

The recommended maximum run out on a driveshaft measured at the shaft centre is:

Correct! Wrong!

You can usually tell if a driveshaft is twisted by placing it on a level floor and making sure the flat surfaces on the yokes are both fully contacting the floor.

Correct! Wrong!

For good cancellation, working angles should be no more than ___________deg. difference on a drive shaft.

Correct! Wrong!

One of the first signs of drive line trouble is usually:

Correct! Wrong!

If a slip yoke is seized-up on interaxle driveshaft damage to the ________________________may occur.

Correct! Wrong!

A driver reports a relatively sudden onset of drive line noise. After a visual examination of the undercarriage, one of the first things to check would be:

Correct! Wrong!

Which of the following will not affect the drive shaft balance?

Correct! Wrong!

U-joints should be lubricated more frequently in excessive road spray conditions.

Correct! Wrong!

What is a good way to separate transmission noise from drive axle or wheel bearing noise?

Correct! Wrong!

A drivershaft without a slip yoke is usually found:

Correct! Wrong!

With parallel driveline alignment if the transmission is at -3 deg. the front differential should be at:

Correct! Wrong!

Before sliding a slip yoke off a stub shaft you should:

Correct! Wrong!

A constant velocity joint eliminates the:

Correct! Wrong!

Phasing of a drive shaft refers to:

Correct! Wrong!

During a routine drive axle oil change, a technician notices a few metal particles on the magnetic plug of the drive axle. What should the technician do first?

Correct! Wrong!

The purpose of a slip yoke and stub shaft (tube shaft) in a drive line is to:

Correct! Wrong!

When greasing a U-joint one should:

Correct! Wrong!

The most common cause of U-joint failure is:

Correct! Wrong!

When replacing driveshaft center support bearings, a technician should always:

Correct! Wrong!

What should a technician check for when replacing U-joints?

Correct! Wrong!

In a full time four wheel drive vehicle, or a tandem drive axle truck what is required in the transfer case/power divider?

Correct! Wrong!

A driveshaft should be able to:

Correct! Wrong!

The maximum recommended length for a drive shaft without a steady bearing is:

Correct! Wrong!

Brinelling of a U-joint is usually caused by:

Correct! Wrong!

A non-constant velocity driveshaft with a working angle speeds up and slows down twice per revolution.

Correct! Wrong!

Ideally the minimum U-joint working angle on heavy duty truck applications should be no more than:

Correct! Wrong!

Steady bearings are adjustable to correct drive line angles.

Correct! Wrong!

Drive Train
You Failed!
You Passed!

Share your Results:

Just tell us who you are to view your results!

Leave a comment

Your email address will not be published. Required fields are marked *